Introduction
In this article, I will you show you ways to allow FTP server traffic through TMG server for outbound connections through Firewall rules and for incoming connections through TMG server publishing rules. We will also cover some special considerations with FTP in Forefront TMG.
Get your copy of the German language "Microsoft ISA Server 2006 - Das Handbuch"
Let’s begin
Note:
Keep in mind that the information in this article is based on a release candidate version of Microsoft Forefront TMG and is subject to change.
A few months ago, Microsoft released RC 1 (Release Candidate) of Microsoft Forefront TMG (Threat Management Gateway), which has a lot of new exciting features.
One of the new features of Forefront TMG is its ability to allow FTP server traffic through the Firewall in both directions. It does this in the form of Firewall access rules for outbound FTP access and with server publishing rules for inbound FTP access through a published FTP Server. This server is located in your internal network or a perimeter network, also known as a DMZ (if you are not using public IP addresses for the FTP Server in the DMZ).
First, I will show you the steps you will need to follow in order to create a Firewall rule which will allow FTP access for outgoing connections through TMG.
FTP access rule
Create a new access rule which allows the FTP protocol for your clients. If you want to allow FTP access for your clients, the clients must be Secure NAT or TMG clients, also known as the Firewall client in previous versions of Forefront TMG.
Please note:
If you are using the Web proxy client, you should note that through this type of client only FTP read-only access is possible and you cannot use a classic FTP client for FTP access, only a web browser FTP access is possible with some limitations.
The following picture shows a FTP access rule.
Figure 1: FTP access rule
A well-known pitfall beginning with ISA Server 2004 is, that by default, after the FTP access rule has been created, the rule only allows FTP read-only access for security purposes in order to prevent users from uploading confidential data outside the organization without permission. If you want to enable FTP uploads you have to right click on the FTP access rule, and then click Configure FTP.
Figure 2: Configure FTP
All you have to do is remove the read only flag, wait for the new FTP connection to be established, and the users get all the necessary permissions to carry out FTP uploads.
Figure 3: Allow write access through TMG
FTP Server publishing
If you want to allow incoming FTP connections to your internal FTP servers, or to FTP servers located in the DMZ, you have to create server publishing rules if the network relationship between the external and the internal/DMZ network is NAT. If you are using a route network relationship, it is possible to use Firewall rules to allow FTP access.
To gain access to an FTP server in your internal network, create an FTP server publishing rule.
Simply start the new Server Publishing Rule Wizard and follow the instructions.
As the protocol you have to select the FTP Server protocol definition which allows inbound FTP access.
Figure 4: Publish the FTP-Server protocol
The standard FTP Server protocol definiton uses the associated standard protocol which can be used for inspection by NIS, if a NIS signature is available.
Figure 5: FTP-Server protocol properties
The Standard FTP Server protocol definition allows FTP Port 21 TCP for inbound access and the protocol definition is bound to the FTP access filter which is responsible for the FTP protocol port handling (FTP Data and FTP control port).
Figure 6: FTP ports and FTP Access Filter binding
Active FTP
One of the changes in Microsoft Forefront TMG is that the Firewall does not allow Active FTP connections by default anymore, for security reasons. You have to manually allow the use of Active FTP connections. It is possible to enable this feature in the properties of the FTP access filter. Navigate to the system node in the TMG management console, select the Applicaton Filters tab, select the FTP Access filter and in the task pane click Configure Selected Filter (Figure 7).
Figure 7: FTP Access filter properties
In the FTP access filter properties select the FTP Properties tab and enable the checkbox Allow Active FTP Access and save the configuration to the TMG storage.
Figure 8: Allow Active FTP through TMG
FTP alerts
Forefront TMG comes with a lot of predefined alert settings for several components and events. One of them is the alert function for the FTP Filter Initialization Warning. This alert informs Administrator when the FTP filter failed to parse the allowed FTP commands.
Figure 9: Configure FTP alert options
The alert actions are almost the same as in ISA Server 2006, so there are no new things to explain for experienced ISA Administrators.
Conclusion
In this article, I showed you some ways to allow FTP access through the TMG Server. There are some pitfalls for a successful FTP implementation. One of the pitfalls is that since the introduction of ISA Server 2004, allowing FTP write access through the Firewall and the other pitfall is new to Forefront TMG. Forefront TMG does not allow Active Mode FTP connections by default, so you have to manually activate this feature if you really need this type of special configuration.
Related links
